Updated Nov 20, 2026· 8 min read

Key takeaways

  • Compare five desk microphone boom arms on load ratings, reach, clamp limits, thread sizes and cable routing for podcasting, streaming and video calls.
⭐ Key Takeaways
Quick answer: Our top pick is Neewer NW-35 Microphone Arm Stand, with InnoGear Boom Arm Microphone Mic Stand as a strong alternative.

A boom arm lifts a microphone off the desk, holds it close to your mouth and swings it aside when the call or recording ends. That single change removes desk thumps from your audio, frees up the surface in front of your keyboard and keeps your mic position identical from one session to the next.

The five arms below cover the main shapes on sale today: two budget scissor arms for light USB microphones, a long-running studio arm in the middle, a low-profile arm that stays below monitor height and a damped premium arm built for heavy broadcast microphones. Every figure quoted comes from the maker listing or published spec sheet for that exact model.

As an Amazon Associate, we earn from qualifying purchases.

Quick answer

The Rode PSA1+ is the safest all-round pick, with damped springs, a 94 gram to 1.2 kilogram microphone range and both a clamp and a desk insert in the box. The Elgato Wave Mic Arm LP suits desks where the arm must stay below monitor height, while the Neewer NW-35 and the InnoGear arm cover light microphones on the budget tier.

The five picks in detail

Neewer NW-35 Microphone Arm Stand

Neewer NW-35 Microphone Arm Stand

Neewer NW-35 Microphone Arm Stand

Check price on Amazon

The NW-35 is the classic folding scissor arm that fills the budget tier of this category. Its maker rates it for microphones up to 1.5 kilograms, which covers most USB condensers and lighter dynamic models, and the arm folds flat against the desk edge when you need the surface back. A microphone clip is included, along with cable ties to keep the lead following the frame.

Because the springs sit outside the frame, the arm is easy to adjust with the tension knob, and the clamp grips desktops up to 2 inches thick according to the model manual. This is the pick for a first desk setup with a light microphone, where the goal is simply getting the mic off its tabletop tripod.

Specs
– Arm type: Suspension scissor arm
– Maximum load: 3.3 lb (1.5 kg)
– Mount: Desk clamp, fits desktops up to 2 in (5.3 cm) thick
– Thread: 3/8 inch, with 3/8 to 5/8 inch adapter
– Microphone clip: Included, holds clips up to 1.26 in (3.2 cm) diameter
– Cable management: Cable ties included
– Material: Steel

InnoGear Boom Arm Microphone Mic Stand

InnoGear Boom Arm Microphone Mic Stand

InnoGear Boom Arm Microphone Mic Stand

Check price on Amazon

InnoGear’s desk arm is another budget scissor design, built from alloy steel with stronger springs than most arms at this tier. The maker quotes a load-bearing capacity of 3.3 pounds, and the base rotates a full 360 degrees, with 135 degrees of back-and-forth extension at the base joint and a metal adapter that turns 270 degrees at the microphone end.

The clamp is shaped for squared desk edges up to 2 inches thick, so it suits most home office desks but not bevelled or curved edges. A standard microphone clip is in the box for dynamic microphones such as handheld-style models, and the whole arm folds away compactly after a session. There is no built-in cable channel, so the lead runs along the outside of the frame.

Specs
– Arm type: Suspension scissor arm
– Maximum load: 3.3 lb (1.5 kg)
– Mount: Desk clamp, fits squared edges up to 2 in thick
– Rotation: 360-degree base rotation
– Item weight: 1.35 lb
– Included: Standard microphone clip
– Cable management: Not stated
– Material: Alloy steel

Rode PSA1 Swivel Mount Studio Microphone Boom Arm

Rode PSA1 Swivel Mount Studio Microphone Boom Arm

Rode PSA1 Swivel Mount Studio Microphone Boom Arm

Check price on Amazon

The PSA1 has been the default studio arm for years, and its published numbers explain why. Rode rates it for microphones between 700 grams and 1.1 kilograms, a range that covers most broadcast dynamic microphones with their mounts. Two mounting options come in the box: a clamp for a desk edge and a threaded insert that fits into a drilled desk hole for a cleaner, fixed installation.

The arm turns through a full circle at the base and holds its position through internal springs, so there are no exposed coils to catch on cables. A 3/8 inch thread sits at the microphone end. If your desk is a permanent recording spot and your microphone sits in that middle weight band, this mid-range arm is the straightforward choice.

Specs
– Arm type: Studio boom arm with internal springs
– Load range: 1.5 to 2.4 lb (700 g to 1.1 kg)
– Mount: Desk clamp and threaded desk insert, both included
– Rotation: 360 degrees
– Thread: 3/8 inch
– Cable management: Hook-and-loop cable wraps
– Item weight: 3.84 lb (1.74 kg)

Elgato Wave Mic Arm LP

Elgato Wave Mic Arm LP

Elgato Wave Mic Arm LP

Check price on Amazon

The Wave Mic Arm LP takes a different route from the scissor arms above: it runs low and horizontal, with the lower arm sitting just 70 millimetres above the desk so the microphone stays below shoulder and monitor height. That makes it the natural pick for anyone on camera, since the arm never crosses the frame of a video call or stream.

Elgato publishes a horizontal reach of 740 millimetres and a vertical reach of 550 millimetres, and the arm is rated for microphones weighing up to 2 kilograms. Thread adapters for 1/4, 3/8 and 5/8 inch mounts are included, the clamp pads the desk edge, and the cable runs inside concealed channels along both arm sections. This is a premium-tier arm, and the published numbers back that placement.

Specs
– Arm type: Low-profile boom arm
– Horizontal reach: 29.1 in (740 mm)
– Vertical reach: 21.7 in (550 mm)
– Lower arm desk clearance: 2.8 in (70 mm)
– Maximum microphone weight: 4.4 lb (2 kg)
– Threads: 1/4, 3/8 and 5/8 inch, adapters included
– Mount: Padded desk clamp
– Cable management: Concealed internal channels
– Item weight: 3.7 lb (1,692 g)

Rode PSA1+ Professional Studio Arm

Rode PSA1+ Professional Studio Arm

Rode PSA1+ Professional Studio Arm

Check price on Amazon

The PSA1+ is Rode’s premium arm, built around a parallelogram spring design with full damping and a neoprene cover over the frame. Rode describes the result as silent movement with no mechanical noise reaching the microphone, which matters when you reposition a mic mid-recording. The supported microphone range is the widest here: from 94 grams up to 1.2 kilograms, so one arm covers a featherweight USB mic and a heavy broadcast dynamic alike.

Like the PSA1, it ships with both a desk clamp and a threaded desk insert, turns a full 360 degrees, and routes the cable through integrated management along the arm. If you record daily, swap between microphones of very different weights, or share a desk with a camera, this is the arm that asks the fewest compromises.

Specs
– Arm type: Parallelogram studio arm, damped springs
– Microphone weight range: 94 g to 1.2 kg (0.2 to 2.6 lb)
– Rotation: 360 degrees
– Mount: Desk clamp and threaded desk insert, both included
– Cable management: Integrated channels, neoprene arm cover
– Reach: Not stated
– Item weight: 3.35 lb
– Model number: PSA1+

How to choose

Match the arm to your microphone weight first. Add the weight of any shock mount you use, then compare the total with the load range the maker publishes. An arm run near the top of its range tends to drift downward over a long session, while an arm built for heavy microphones can push a very light mic upward. The PSA1+ publishes the widest window, from 94 grams to 1.2 kilograms; the budget scissor arms top out at 1.5 kilograms but hold light microphones more happily than heavy ones.

Check your desk edge next. Every arm here clamps to an edge up to about 2 inches thick, and the InnoGear clamp wants a squared edge rather than a bevelled one. Glass desks and very thick worktops rule out most clamps; the two Rode arms answer that with a threaded desk insert that mounts through a drilled hole. Measure before ordering, and leave room behind the clamp for the arm’s turning circle.

Think about height and camera framing. A scissor arm reaches up and over, which suits audio-only recording. A low-profile arm like the Elgato LP runs beneath monitor height, keeping sight lines and webcam frames clear. Finally, look at thread sizes: most arms here use 3/8 or 5/8 inch microphone threads, and the Elgato and Neewer include adapters, which saves a separate purchase when your microphone and arm disagree.

Who should skip

Skip the boom arm entirely if your microphone lives on a desk you share or clear daily, since a clamped arm is semi-permanent furniture. A small desktop tripod or the stand bundled with your microphone will serve you better. Also skip these five if your microphone and mount together weigh more than 2 kilograms, because none of the arms here is rated above that figure; a floor stand with a boom section is the safer tool for very heavy studio condensers.

Budget scissor arms are the wrong buy for a heavy broadcast dynamic microphone near their limit, and low-profile arms are wasted on an audio-only desk where nothing blocks the taller path of a scissor design. If your desk has no free edge at all, look at a wall mount or a weighted desktop stand instead of forcing a clamp onto a rounded edge.

FAQ

Will a boom arm hold a heavy broadcast microphone?

Yes, within its published range. The Rode PSA1+ accepts microphones up to 1.2 kilograms and the Elgato Wave Mic Arm LP up to 2 kilograms, both enough for large dynamic broadcast models with a mount fitted. The budget scissor arms are rated to 1.5 kilograms on paper, but they sit happier with light and mid-weight microphones.

What desk thickness can a boom arm clamp handle?

The clamps on the Neewer NW-35 and the InnoGear arm fit edges up to 2 inches thick, and the InnoGear specifies a squared, flat edge. The two Rode arms add a threaded desk insert as a second option, which suits thicker worktops where a clamp cannot grip.

Do boom arms fit every microphone thread size?

Most microphone mounts use 3/8 or 5/8 inch threads. The Elgato Wave Mic Arm LP includes adapters for 1/4, 3/8 and 5/8 inch, and the Neewer NW-35 includes a 3/8 to 5/8 inch adapter, so both connect to the common sizes without extra parts. The Rode arms use a 3/8 inch thread at the microphone end.

Is a low-profile arm better than a scissor arm?

Neither is better outright; they solve different desk problems. A low-profile arm keeps the microphone below monitor and shoulder height, which suits video calls and streaming. A scissor arm reaches higher and folds flatter against the desk edge, which suits audio-only recording and smaller desks.

Final verdict

For most desks, the Rode PSA1+ is the arm to buy: the widest published weight range, damped silent movement and two mounting options cover nearly every home studio. Choose the Elgato Wave Mic Arm LP if you appear on camera and need the arm out of frame. On the budget tier, the Neewer NW-35 and InnoGear arm both lift a light USB microphone off the desk for very little outlay, and the Rode PSA1 remains the mid-range default for a fixed recording desk with a mid-weight microphone.

C
ChartGet Editorial Team
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Microphone Boom Arms for Podcasting and StreamingCheck price on Amazon

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free
Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account

As an Amazon Associate we earn from qualifying purchases.